This is the output for flashmode:
S1 Boot U8500 1240-4128 CRH1099189_R10E010 2012-03-27 11:03 (RioGrande (DB8500) chipset)
SoC settings: INFO: @(#)SOC-SETTINGS v4.0.1-(F)-batt-volt db8500 v2 1000Mhz Sep 14 2012 14:35:17
SoC
SoC settings: INFO: VBATT_VOLT_USB usb line 0x00000010 0x00000002
SoC settings: INFO: BattOK reg 0x000000c5
SoC settings: INFO: VBATT_VOLT_USB usb line 0x00000010 0x00000002
SoC settings: INFO: VBat 0x00000000 0x0000024d
SoC settings: INFO: No memory mounted on CS1
SoC settings: INFO: Vendor ID = 0x00000001, CS0 density = 0x00000018, CS1 density = 0x00000000
SoC settings: INFO: CS0 revision ID1 = 0x00000001, CS0 revision ID2 = 0x00000000
SoC settings: INFO: AVS Enable, FVR21 value = : 0x8719104c, FVR22 value = : 0x0023ddf2
MB), CS0 (512 MB) CS1 (0 MB)
SoC settings: INFO: DDR Test Ended successfully.
SoC settings: INFO: Requesting 1GHz from PRCMU
SoC settings: INFO: Set 1GHz OK
ISSW returned from MEMINIT, vendor: Samsung (0x01), density (CS0): 4Gbit (0x18), density (CS1): Unknown! (0x00)
MEMINIT passed OK
DB CutId:008500B2
AB CutId:33
ISSW version:R1G-EC13 P2D With "0001-ISSW-Clean-caches-on-wd-reset.patch" and mem_issw=1M@160M
MEMINIT version:02
PRCMU firmware version:03.3F.05 (for 8500 chipset)
Using MEMINIT from platform
Using PRCMU firmware from platform
AB8500 Turn on status: 0x20 ( VbusDetect. )
AB8500 Reset status: 0x00
DB8500 Reset status: 0x0020 ( Power on reset. )
AB8500 Switch Off : 0x20 ( PornVbat )
TA ELF address buffer (secure mode): 0x4000700C
plf_GetStartupReasonBitfield S1 Boot Startup info: [USB INSERTED]
Found i2c controller
Found i2c controller
MID 0: Samsung MMC 'M8G2FB' 7.288 GB
S1 Boot "1240-4128 U8500 CRH1099189_R10E010" (2012-03-27 11:03)
Reboot reason: 0x0 (Coldboot)
ControlledRooting: Status = [Not Allowed]
FlaFla is set
plf_kbd.c(194): Key(s) is Pressed (ROW|COL): [0006]
S1 BOOT check if any USB connection...
and when I try to go in to fastboot (volume up):
S1 Boot U8500 1240-4128 CRH1099189_R10E010 2012-03-27 11:03 (RioGrande (DB8500) chipset)
SoC settings: INFO: @(#)SOC-SETTINGS v4.0.1-(F)-batt-volt db8500 v2 1000Mhz Sep 14 2012 14:35:17
SoC settings: INFO: BattOK reg 0x000000c5
SoC settings: INFO: VBATT_VOLT_USB usb line 0x00000000 0x00000000
SoC settings: INFO: BattOK reg 0x000000c5
SoC settings: INFO: VBATT_VOLT_USB usb line 0x00000000 0x00000000
SoC settings: INFO: VBat 0x00000000 0x0000024d
SoC settings: INFO: No memory mounted on CS1
SoC settings: INFO: Vendor ID = 0x00000001, CS0 density = 0x00000018, CS1 density = 0x00000000
SoC settings: INFO: CS0 revision ID1 = 0x00000001, CS0 revision ID2 = 0x00000000
SoC settings: INFO: AVS Enable, FVR21 value = : 0x8719104c, FVR22 value = : 0x0023ddf2
SoC settings: INFO: Memory size=0x20000000 (512 MB), CS0 (512 MB) CS1 (0 MB)
SoC settings: INFO: DDR Test Ended successfully.
SoC settings: INFO: Requesting 1GHz from PRCMU
SoC settings: INFO: Set 1GHz OK
ISSW returned from MEMINIT, vendor: Samsung (0x01), density (CS0): 4Gbit (0x18), density (CS1): Unknown! (0x00)
MEMINIT passed OK
DB CutId:008500B2
AB CutId:33
ISSW version:R1G-EC13 P2D With "0001-ISSW-Clean-caches-on-wd-reset.patch" and mem_issw=1M@160M
MEMINIT version:02
PRCMU firmware version:03.3F.05 (for 8500 chipset)
Using MEMINIT from platform
Using PRCMU firmware from platform
AB8500 Turn on status: 0x20 ( VbusDetect. )
AB8500 Reset status: 0x00
DB8500 Reset status: 0x0020 ( Power on reset. )
AB8500 Switch Off : 0x20 ( PornVbat )
TA ELF address buffer (secure mode): 0x4000700C
plf_GetStartupReasonBitfield S1 Boot Startup info: [USB INSERTED]
Found i2c controller
Found i2c controller
MID 0: Samsung MMC 'M8G2FB' 7.288 GB
S1 Boot "1240-4128 U8500 CRH1099189_R10E010" (2012-03-27 11:03)
Reboot reason: 0x0 (Coldboot)
ControlledRooting: Status = [Not Allowed]
FlaFla is set
plf_kbd.c(194): Key(s) is Pressed (ROW|COL): [0005]
Fastboot key trigger active
No Service Mode detected.
boot_partitions: The following partitions will be booted (in this order):
partID:8000
partID:05
partID:03
load_and_verify_elf (fastboot): Simlock verification failed, will not allow fastboot since SIN verification is enforced for partition 32768
plf_boot_elf: ERROR: Invalid parameters!
boot_partitions: plf_boot_elf FAILED for partition 32768!
plf_boot_elf: Starting booting of partID:05
plf_boot_elf (modem boot): Modem version info:
NWM_STACK=MB10A_12w22_2_06092
MODEM_DELIVERY=49020905
MODEM_VARIANT=SONY2020
plf_boot_elf (modem boot): Booting started
plf_boot_elf: Starting booting of partID:03
ATAG list starts at 0x00000100
Kernel commandline: startup=0x4 warmboot=0x0 ta_info=9,4,256 androidboot.bootloader=s1 androidboot.serialno=BX90308H4X cachepolicy=writealloc noinitrd init=init board_id=1 logo.nologo root=/dev/ram0 rw rootwait console=null androidboot.console=null androidboot.hardware=st-ericsson mem=96M@0 mem_mtrace=15M@96M mem_mshared=1M@111M mem_modem=16M@112M mem=32M@128M mem_issw=1M@160M hwmem=71M@161M mem=280M@232M mpcore_wdt.mpcore_margin=359 end semcandroidboot.babe1324=42583930333038483458
Vibrate OFF
[Last word from S1 BOOT] Jumping to kernel at address [0x00008000], all your base are belong to us!
Uncompressing Linux... done, booting the kernel.