# Note: The letters in this file are NOT case sensitive.
dot11BeaconPeriod = 100
ConnSelfTimeout = 60000
SmeConnectMode = 1 #0 - auto, 1 - manual
ScanResultAging = 0 # in Second - range 0..1000
WME_Enable = 1 #0=diable WME support / 1=Enable
dot11NetworkType = 3 #2 - A only mode, 3 - B/G mode, 4 - A/G Dual mode
SmeScanGChannelList = 1,2,3,4,5,6,7,8,9,10,11,12,13,14
SmeScanAChannelList = 36,40,44,48,52,56,60,64
RecoveryEnable = 1 #0 -Disabled 1- Enabled
BThWlanCoexistEnable = 1 #0 - SG disable, 1 - SG protective
TxAggregationPktsLimit = 0 # Disable Tx packets aggregation for Linux (degrades TP)
#
# Power Manager
#
BeaconListenInterval = 1 # the number of N-Beacon or N-DTim
DtimListenInterval = 1 #
ReAuthActivePriority = 0
dot11PowerMode = 1 #0 - Auto
#1 - Active
#2 - Short Doze
#3 - Long Doze
PowerMgmtHangOverPeriod = 10 #in mSec units
AutoPowerModeDozeMode = 3 #2 - Short Doze
#3 - Long Doze
AutoPowerModeActiveTh = 2 #packets per second
AutoPowerModeDozeTh = 8 #packets per seconds - threshold for entering ELP in Auto mode
defaultPowerLevel = 2 #0 - ELP
#1 - PD
#2 - AWAKE
PowerSavePowerLevel = 2 #0 - ELP
#1 - PD
#2 - AWAKE
DcoItrimEnabled = 0 # 0 - Disabled 1 - Enabled
DcoItrimModerationTimeout = 50000
TxPower = 205 #set Default Tx Power Level in DBM * 10
dot11FragmentationThreshold = 4096
dot11RTSThreshold = 4096
WPAMixedMode= 1
RSNPreAuthentication = 1
CalibrationChannel24 = 7
CalibrationChannel5 = 36
# Regulatury Domain tables.
# Each byte correlates to one channel in sequential order. Table 2.4 starts from channel 1, Table 5.0 starts from channel 36.
# Bits 0..4 - Max power allowed in Dbm.
# Bit 6 - Channel is allowed for Active scan
# BIt 7 - Channel is allowed
AllowedChannelsTable24 = FFFFFFFFFFFFFFFFFFFFFFFFFFFF
AllowedChannelsTable5 = FF000000FF000000FF000000FF000000FF000000FF000000FF 000000FF000000000000000000000000000000000000000000 0000000000000000000000000000FF000000FF000000FF0000 00FF000000FF000000FF000000FF000000FF000000FF000000 FF000000FF0000000000000000FF000000FF000000FF000000 FF000000FF000000000000000000000000000000
SpectrumManagement = 0 # 0 - Disable 802.11h, 1 - Enable
RxBroadcastInPs = 1
#arp ip filter - must be written 8 characters for example 10.2.43.3 -> 0a 02 2b 21 and not a 2 2b 21
ArpIp_Addr = 0a 02 0a b7
ArpIp_Filter_ena = 0
#mac filter
Mac_Filter_Enabled = 0
numGroupAddrs = 4
Group_addr0 = 10 01 02 03 04 05
Group_addr1 = 11 11 12 13 14 15
Group_addr2 = 12 21 22 23 24 25
Group_addr3 = 13 31 32 33 34 35
Group_addr4 = 14 41 42 43 44 45
Group_addr5 = 15 51 52 53 54 55
Group_addr6 = 16 61 62 63 64 65
Group_addr7 = 17 71 72 73 74 75
#beacon filter
Beacon_Filter_Desired_State = 1
Beacon_Filter_Stored = 1
#beacon IE table
#the size is the len of the string - spaces = number of bytes
Beacon_IE_Num_Of_Elem = 16
Beacon_IE_Table_Size = 37
Beacon_IE_Table = 00 01 01 01 32 01 2a 01 03 01 06 01 07 01 20 01 25 01 23 01 30 01 28 01 2e 01 3d 01 85 01 dd 01 00 52 f2 02 00 01
# rate policy - short / long retries
RatePolicyUserShortRetryLimit = 10
RatePolicyUserLongRetryLimit = 10
#rate policies
#rates guide: -->>mcs7,msc6,mcs5,mcs4,mcs3,mcs2,mcs1,mcs0,54,58,36 ,24,22,18,12,11,9,6,5.5,2,1
OsDbgState = 0x01e9003c # -1 or 0xffffffff -all (opens debug messages in o.s. only - sevirity+modules)
################################################## ###########
# Configure the severity table (0 = Disable/ 1 = Enable)
#
# Byte #0: Init
# Byte #1: Information
# Byte #2: Warning
# Byte #3: Error
# Byte #4: Fatal Error
# Byte #5: SM
# Byte #6: Console
################################################## ###########
# LAUNCH Logging Mask
ReportSeverityTable = 0000000
# Default Logging Mask
# ReportSeverityTable = 0001101
BeaconReceiveTime = 50
#
# QOS UPSD
#
desiredPsMode = 1 # Global Power save delivery protocol (1 - UPSD, 0 - Legacy)
QOS_wmePsModeBE = 1 # Power save delivery protocol for BE AC (1 - UPSD, 0 - Legacy)
QOS_wmePsModeBK = 1 # Power save delivery protocol for BK AC (1 - UPSD, 0 - Legacy)
QOS_wmePsModeVI = 1 # Power save delivery protocol for VI AC (1 - UPSD, 0 - Legacy)
QOS_wmePsModeVO = 1 # Power save delivery protocol for VO AC (1 - UPSD, 0 - Legacy)
#
# QOS Classifier
#
Clsfr_Type = 1 # 1 - DSCP, 2 - Port, 3 - IP+port
NumOfCodePoints = 4
DSCPClassifier00_CodePoint = 0 #Best Effort
DSCPClassifier00_DTag = 0
DSCPClassifier01_CodePoint = 8 #Background
DSCPClassifier01_DTag = 1
DSCPClassifier02_CodePoint = 40 #Video
DSCPClassifier02_DTag = 5
DSCPClassifier03_CodePoint = 56 #Voice
DSCPClassifier03_DTag = 6
dot11MaxReceiveLifetime=512000
WiFiAdhoc = 0
WiFiWmmPS = 0 # Use 1 on WiFi test in order to configure PS to work in WMM mode
TriggeredScanTimeOut = 50000 # Maximum time in Us between 2 channels on triggered scan
# PsPoll delivery failure solution
PsPollDeliveryFailureRecoveryPeriod = 20 # Time in Ms to stay ACTIVE ('0' to disable feature)
ConsecutivePsPollDeliveryFailureThreshold = 4 # Number of failed PsPoll's to start ACTIVE time out
#Auto Rx streaming
PsTrafficPeriod = 20
# Weights in percent for RSSI/SNR Average calculations
RssiBeaconAverageWeight = 20
RssiPacketAverageWeight = 10
SnrBeaconAverageWeight = 20
SnrPacketAverageWeight = 10
HT_Enable=1 #0=diable 802.11n support / 1=Enable
IbssProtectionType = 1 # 0 = CTS protaction disable ; 1 = Standard CTS protaction
BurstModeEnable = 0 # 0 - Disabled 1 - Enabled
RoamScanEnable = 1 # 1- roaming and immidate scan enable by deafult 0- allowing roaming & scannig due to CLI confguration
RoamingOperationalMode = 1 # 0=Manual , 1=Auto
SendTspecInReassPkt = 0 # 0=do not send, 1=send
FmCoexuSwallowPeriod = 5
FmCoexuNDividerFrefSet2 = 12
FmCoexuMDividerFrefSet2 = 148
BaPolicyTid_0 = 3
################################################## ################################################## ##########################
################################################## Radio parameters data - Start #############################################
################################################## ################################################## ##########################
################################ General parameters ################################
STRFRefClock = 9 # Unit: Options 5'bXX000 : Bit 0,1,2 - (0: 19.2MHz; 1: 26MHz; 2: 38.4MHz (Default); 3: 52MHz; 4: 38.4MHz XTAL) ;
# 5'bX0XXX : Bit 3 - CLK_REQ type; 0 = wired-OR (Default) , 1= push-pull
# 5'b0XXXX : Bit 4 - CLK_REQ polarity; 0 = Normal (Default) , 1=Inverted, Format: Unsigned, Source: Customer
STRFRefClockSettingTime = 5
TXBiPFEMAutoDetect = 0 # Unit: Options (0: Manual Mode; 1: Automatic mode), Format: Unsigned, Source: Customer
TXBiPFEMManufacturer = 1 # Unit: Options (0: RFMD; 1: Triquint), Format: Unsigned, Source: Customer
ClockValidOnWakeup = 0
DC2DCMode = 0 # Unit: Options (0: btSPI is not used; 1: mux DC2DC mode to BT_FUNC2), Format: Unsigned, Source: Customer
Single_Dual_Band_Solution = 0 # Unit: Options (0: Single band. 2.4GHz only; 1: Dual band = 2.4GHz and 5GHz solution), Format: Unsigned, Source: Customer
Settings = 65 # 0x41 Unit: Options (Bit0: NBI (0: Off; 1: On), Bit1: Telec channel 14 (0: Off; 1: On), Format: Unsigned, Source: Customer
# Bit2: FEM0-LB, Bit3: FEM0-HB, Bit4: FEM1-LB, Bit5: FEM1-HB - TX BiP load (0: Internal; 1: External),
# Bit6: LPD Low band, Bit7: LPD High band
# Smart Reflex params
SRState = 0 # Unit: Options ( 1 - Enabled / 0- Disabled) Format: Decimal, Source: TI
#SRF1 = 07,03,18,10,05,fb,f0,e8, 0,0,0,0,0,0,0f,3f # Unit: SRF1 values, Format: Signed, Source: TI
#SRF2 = 07,03,18,10,05,f6,f0,e8 # Unit: SRF2 values, Format: Signed, Source: TI
#SRF3 = 07,03,18,10,05,fb,f0,e8 # Unit: SRF3 values, Format: Signed, Source: TI
################################ FEM dependents parameters #######################################
###################### FEM1 parameters ######################
# (for Single bend 2.4G parameters FEM1 (TQS 2.5) HDK20)
RxTraceInsertionLoss_2_4G = 0
TXTraceLoss_2_4G = 0
RxRssiAndProcessCompensation_2_4G = ec,f6,00,0c,18,f8,fc,00,08,10,f0,f8,00,0a,14
TXBiPReferencePDvoltage_2_4G = 375 # 0x177
TxBiPReferencePower_2_4G = 128 # 0x80
TxBiPOffsetdB_2_4G = 0
TxPerRatePowerLimits_2_4G_Normal = 1d, 1f, 22, 26, 27, 27
TxPerRatePowerLimits_2_4G_Degraded = 1a, 1f, 22, 24, 26, 27
TxPerRatePowerLimits_2_4G_Extreme = 16, 1d, 1e, 20, 24, 25 # Unit: 1/2dB, Format: Signed, Source: Customer
DegradedLowToNormalThr_2_4G = 30 # 0x1e Unit: 1/10 volts, Format: Unsigned, Source: TI
NormalToDegradedHighThr_2_4G = 45 # 0x2d Unit: 1/10 volts, Format: Unsigned, Source: TI
TxPerChannelPowerLimits_2_4G_11b = 50,50,50,50,50,50,50,50,50,50,50,50,50,50
TxPerChannelPowerLimits_2_4G_OFDM = 22,50,50,50,50,50,50,50,50,50,50,50,50,50
TxPDVsRateOffsets_2_4G = 01,02,02,02,02,00
# for Triquent 2.5 should use this, but needs factory OTP support, for now use the same as Triquent 2.6
#TxIbiasTable_2_4G = 11,11,15,11,15,0f
TxIbiasTable_2_4G = 15,15,15,11,15,0f
RxFemInsertionLoss_2_4G = 14 # 0x0e
###################### FEM0 parameters #########################
# (for Single bend 2.4G parameters FEM0 (RFMD 3.5) HDK20)
#RxTraceInsertionLoss_2_4G = 0
#TXTraceLoss_2_4G = 0
#TXBiPReferencePDvoltage_2_4G = 335 # Length: 1; Unit: 1mV; Format: Unsigned; Source: TI; Comment: This parameter define the reference point of the FEM power detector
#TxBiPReferencePower_2_4G = 128 # Length: 1; Unit: 1/8dB; Format: Signed; Source: TI; Comment: Reference output power that produces given reference power detector output voltage .
#TxBiPOffsetdB_2_4G = 0 # Length: 1; Unit: 1/8dB; Format: Signed; Source: Customer; Comment: This field is used to fine-tune the TX BiP by the customer
#TxPerRatePowerLimits_2_4G_Normal = 1d,1f,22,26,27,29 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
#TxPerRatePowerLimits_2_4G_Degraded = 19,1f,22,25,25,27 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
#TxPerRatePowerLimits_2_4G_Extreme = 16,1d,1e,20,24,25 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
#DegradedLowToNormalThr_2_4G = 30 # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
#NormalToDegradedHighThr_2_4G = 45 # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
#TxPerChannelPowerLimits_2_4G_11b = 50,50,50,50,50,50,50,50,50,50,50,50,50,50 # Length: 14; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The purpose of this table is to allow clipping of the maximum output power on certain channels
#TxPerChannelPowerLimits_2_4G_OFDM = 50,50,50,50,50,50,50,50,50,50,50,50,50,50 # Length: 14; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The purpose of this table is to allow clipping of the maximum output power on certain channels
#TxPDVsRateOffsets_2_4G = 01,02,02,02,02,00 # Length: 6; Unit: 1/8dB; Format: Signed; Source: TI; Comment: This parameter is a power detector offset value used to correct the power detector curve for each rate group
#TxIbiasTable_2_4G = 31,31,36,36,3b,3b # Length: 6; Unit: Codeword ; Format: Unsigned; Source: TI; Comment: This parameter sets the bias current provided by the SoC to the PA in the FEM. Options (MCS7, 54/48, 36/24, 18/12, 9/6, 11b)
#RxFemInsertionLoss_2_4G = 14 # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: TI; Comment: This parameter specifies the received insertion loss of the WL127x
################################################## ################################################## ##########################
################################################## Radio parameters data - End ###############################################
################################################## ################################################## ##########################